Counterpath Bria 3.1 for Mac User Guide - Enterprise Deploymen Manual de usuario Pagina 60
- Pagina / 72
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CounterPath Corporation
56
Field Description
Headset Mode
Microphone
Speaker
Change these fields only if you want to override the devices that Bria automatically selected.
In both these fields, select the headset you are using.
The headset is the device that is usually used for audio out (the sound you hear) and audio in
(recording your voice). The only situation in which the headset is not used is when the Speaker
Phone button on the dialpad is pressed.
Therefore, unless you will always be using Bria in speakerphone mode, you must make a selection
here.
Select the headset in both the Speaker device field and Microphone device field.
Zero touch device
configuration
Typically, leave on. When device configuration is on, if you change your audio or video device,
Bria will automatically detect the new device and start using it.
Test Devices For information on the Test Devices button, see “Troubleshooting” on page 61.
Speakerphone Mode
Microphone Change this field only if you want to override the devices that Bria automatically selected.
Make the appropriate choice:
• Select the device that you want to use for audio in (recording your voice) when the Speaker
Phone button is pressed.
It can be any microphone: it does not have to be the microphone on the device you specified as
the speaker device. For example, it can be the microphone on your camera.
• Select None if you do not have a speaker phone. The Speaker Phone button on the dialpad is
disabled.
Speaker Change this field only if you want to override the devices that Bria automatically selected.
Make the appropriate choice:
• Select the device that you want to use for audio out (the sound you hear) when the Speaker
Phone button is pressed. Make sure you select a speaker device (not the headset).
• Select None if you do not have a speaker phone. The Speaker Phone button on the dialpad is
disabled.
Other Devices
Ring on The device where you want to hear the phone ringing.
Change this field only if you want to override the devices that Bria automatically selected.
Volume The volume of the ringer.
Camera This field appears only on versions of Bria that include video functionality.
Change this field only if you want to override the devices that Bria automatically selected.
Select the camera model.
Resolution Leave at standard, or change the size as follows:
• Set it to high if you have a good camera and a computer with a fast CPU. You will know that you
have set the size too large if:
Your computer slows down (the video is using too much CPU)
The video shows black areas or is slow or jerky.
• Typically set it to low only in special situations, for example, when using wi-fi in a hotel. You
will know that you have set the size too small if the video is fuzzy.
This field is identical to the Resolution field in Media Quality > Video Quality.
Deskphone Setup If you are set up with a deskphone, click to configure the URI of your deskphone, in order to work
in deskphone mode. See page 26.
- Bria 3 for Mac User Guide 1
- Contents 3
- 1 Introduction 5
- 2 Installation and Setup 7
- 2.2 Starting Bria 8
- 2.3 Configuring Bria 9
- 2.4 Setting up a Contact List 10
- 2.5 Setting up for Presence 11
- 2.6 Troubleshooting 12
- 2.7 Checking for Bria Updates 12
- 3Using Bria 13
- The Bria Menu 14
- 3.2 Placing a Call 15
- Call entry field 16
- Click to place the call 16
- Auto complete suggestions 16
- CounterPath Corporation 16
- Letters to Numbers 17
- Placing another Call 18
- Ending a Call 18
- 3.3 Handling Incoming Calls 19
- Auto Answer 20
- 3.5 Transfering a Call 22
- 3.6 Handling Video Calls 24
- Adding Video 25
- Other Party Adds Video 25
- Pausing and Resuming Video 25
- 3.7 Conference Calls 26
- Managing the Conference 27
- Video Conference Calls 28
- 3.8 Voicemail 29
- 3.9 Forwarding Calls 29
- Set up for Deskphone Mode 30
- Working in Deskphone Mode 30
- 3.11 Instant Messaging 31
- Sending a Broadcast IM 32
- Conference IM—Group Chat 33
- Viewing the IM Archive 34
- Sending Files 35
- Receiving Files 35
- 4 The Contacts Tab 37
- Address label “softphone” 38
- Address type “Phone” 38
- Importing Contacts 39
- Adding a Contact 40
- Modifying the Contact List 41
- 4.3 Using Contacts 42
- 4.4 Sharing Online Status 43
- Setting the Presence Account 44
- Setting your Online Status 45
- 4.5 Privacy 47
- 5 Using Other Resources 49
- 5.2 The Favorites Tab 50
- 5.3 The Directory Tab 51
- 6 Configuring Bria 53
- 6.2 General Preferences 56
- Preferences – Privacy 57
- Enable Alert Displays 58
- Assigning Sounds 58
- Preferences – Devices 59
- Preferences – Network 61
- Preferences – Codecs 61
- Preferences – Media Quality 62
- Preferences – Call Automation 63
- Preferences - Directory 63
- Preferences – Contact Storage 63
- Preferences – Advanced 64
- A Troubleshooting 65
- Testing Video Quality 66
- Testing Audio Devices 67
- Diagnostics 68
- B Contact List Headings 69
- C Glossary 70
Relacionado con productos y manuales para Software Counterpath Bria 3.1 for Mac User Guide - Enterprise Deploymen
(82 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales